|
Author
|
Topic: Motor ID help
|
Fastymz
Moderator Posts: 22791
From: Reno Nv M&M #1240
Registered: Apr 2001
|
posted 09-19-2006 09:49 PM
 
I picked up a complete 289 today.
These are the motor codes,
6F17
C5AE-6015E
Best I can tell it's a 65-66 block from a full size car?Intake is a 4v number C60E-9425-B I also got a short block 302 E7 code. ------------------
oddly obsessed with big scoops on little Mustangs HOOD HACKERS DELIGHT!
My Pics 13.563 @ 108.64 [This message has been edited by Fastymz (edited 09-19-2006).]
|
kcode
Gearhead Posts: 3415
From: alvaton,ky,usa Suburb of Bowling Green, M&M #79, MCA #29208
Registered: Jun 99
|
posted 09-19-2006 10:36 PM
Scoop,
From the info you posted theres not enough info to tell what the motor was from. Most all of the 289 Cleveland blocks would have the same casting number until later in the year and the Windsor plant started casting blocks.The block and intake could be for a 66 if the intake was original. I don't recall Ford offering a 4 barrel 289 in a full size car in 65 or 66. A Fairlane or Mustang would be a better guess. Is there a motor tag on the intake anywhere? BTW the intake number should be 9425Mike [This message has been edited by kcode (edited 09-19-2006).]
|
Fastymz
Moderator Posts: 22791
From: Reno Nv M&M #1240
Registered: Apr 2001
|
posted 09-19-2006 10:41 PM
Mike, there isn't a tag anywhere. The heads have the WF stamped under the valve covers.
The was said to be pulled from a 67 Mustang that was already some one else's hot rod.
I was told the motor ran when pulled some 15 years ago or so???Thanks your right about the intake number. 
------------------
oddly obsessed with big scoops on little Mustangs
HOOD HACKERS DELIGHT!
My Pics 13.563 @ 108.64 [This message has been edited by Fastymz (edited 09-19-2006).]
|
Fastymz
Moderator Posts: 22791
From: Reno Nv M&M #1240
Registered: Apr 2001
|
posted 09-21-2006 12:01 AM
Is any other way to find more about the motor beside the ID tag?------------------
oddly obsessed with big scoops on little Mustangs HOOD HACKERS DELIGHT!
My Pics 13.563 @ 108.64
|
senzstang
Gearhead Posts: 530
From: perry, oh, usa
Registered: May 2002
|
posted 09-21-2006 08:30 AM
quote:
Originally posted by Fastymz:
Is any other way to find more about the motor beside the ID tag?
I am going from memory so bare with me!
I believe that on the block where the starter would normaly be covering, there should be some codes stamped into the block. Also, there should be codes on the heads under the valve covers. You found the WF but there are more numbers in there. Sorry to be so vague. Phil
|
kcode
Gearhead Posts: 3415
From: alvaton,ky,usa Suburb of Bowling Green, M&M #79, MCA #29208
Registered: Jun 99
|
posted 09-21-2006 10:48 PM
Scoop,
Unless you find the VIN stamp on the block you are out of luck. Even with the tag, it would not specify the vehicle it originally was installed, only displacement, date code and level changes, and place of manufacture.Sorry, Mike
|
